So that connections are protected from failing from on-path attacks.
Decryption failure of long packets used during handshake still leads
to connection close since it barely makes sense to handle them there.
A previously used undefined error code is now replaced with the generic one.
Note that quic-transport prescribes keeping connection intact, discarding such
QUIC packets individually, in the sense that coalesced packets could be there.
This is selectively handled in the next change.
The patch removes remnants of the old state tracking mechanism, which did
not take into account assimetry of read/write states and was not very
useful.
The encryption state now is entirely tracked using SSL_quic_read/write_level().
quic-transport draft 29:
section 7:
* authenticated negotiation of an application protocol (TLS uses
ALPN [RFC7301] for this purpose)
...
Endpoints MUST explicitly negotiate an application protocol. This
avoids situations where there is a disagreement about the protocol
that is in use.
section 8.1:
When using ALPN, endpoints MUST immediately close a connection (see
Section 10.3 of [QUIC-TRANSPORT]) with a no_application_protocol TLS
alert (QUIC error code 0x178; see Section 4.10) if an application
protocol is not negotiated.
Changes in ngx_quic_close_quic() function are required to avoid attempts
to generated and send packets without proper keys, what happens in case
of failed ALPN check.
quic-transport draft 29, section 14:
QUIC depends upon a minimum IP packet size of at least 1280 bytes.
This is the IPv6 minimum size [RFC8200] and is also supported by most
modern IPv4 networks. Assuming the minimum IP header size, this
results in a QUIC maximum packet size of 1232 bytes for IPv6 and 1252
bytes for IPv4.
Since the packet size can change during connection lifetime, the
ngx_quic_max_udp_payload() function is introduced that currently
returns minimal allowed size, depending on address family.
quic-tls, 8.2:
The quic_transport_parameters extension is carried in the ClientHello
and the EncryptedExtensions messages during the handshake. Endpoints
MUST send the quic_transport_parameters extension; endpoints that
receive ClientHello or EncryptedExtensions messages without the
quic_transport_parameters extension MUST close the connection with an
error of type 0x16d (equivalent to a fatal TLS missing_extension
alert, see Section 4.10).
This is a temporary workaround, proper retransmission mechanism based on
quic-recovery rfc draft is yet to be implemented.
Currently hardcoded value is too small for real networks. The patch
sets static PTO, considering rtt of ~333ms, what gives about 1s.
Also, if both are present, require that they have the same value. These
requirements are specified in HTTP/3 draft 28.
Current implementation of HTTP/2 treats ":authority" and "Host"
interchangeably. New checks only make sure at least one of these values is
present in the request. A similar check existed earlier and was limited only
to HTTP/1.1 in 38c0898b6df7.
The flags was originally added by 8f038068f4bc, and is propagated correctly
in the stream module. With QUIC introduction, http module now uses datagram
sockets as well, thus the fix.
Previously, invalid connection preface errors were only logged at debug
level, providing no visible feedback, in particular, when a plain text
HTTP/2 listening socket is erroneously used for HTTP/1.x connections.
Now these are explicitly logged at the info level, much like other
client-related errors.
When enabled, certificate status is stored in cache and is used to validate
the certificate in future requests.
New directive ssl_ocsp_cache is added to configure the cache.
OCSP validation for client certificates is enabled by the "ssl_ocsp" directive.
OCSP responder can be optionally specified by "ssl_ocsp_responder".
When session is reused, peer chain is not available for validation.
If the verified chain contains certificates from the peer chain not available
at the server, validation will fail.
Previously only the first responder address was used per each stapling update.
Now, in case of a network or parsing error, next address is used.
This also fixes the issue with unsupported responder address families
(ticket #1330).
Preserving pointers within the client buffer is not needed for HTTP/3 because
all data is either allocated from pool or static. Unlike with HTTP/1, data
typically cannot be referenced directly within the client buffer. Trying to
preserve NULLs or external pointers lead to broken pointers.
Also, reverted changes in ngx_http_alloc_large_header_buffer() not relevant
for HTTP/3 to minimize diff to mainstream.
New field r->parse_start is introduced to substitute r->request_start and
r->header_name_start for request length accounting. These fields only work for
this purpose in HTTP/1 because HTTP/1 request line and header line start with
these values.
Also, error logging is now fixed to output the right part of the request.
